33mm Syringe Filter for Filtration

They are also very useful in the protection of vacuum pump pipelines and have the qualities of high absorption and retention capacity. Due to their advantages, these syringes can be used in laboratory situations as well as industrial applications.

Aijiren brand syringe filters are HPLC certified to ensure reliable and consistent results. Water, methanol, and acetonitrile are used for testing, and HPLC is used for detection at 210 and 254 nm wavelengths. None absorbs ultraviolet light, which can provide a purer analytical background.

Instructions for use and precautions:
1. It must be used with disposable syringes and glass syringes. The interface is standard. Put the needle filter on the syringe first, then pour the liquid into the syringe, press the push rod down, and collect the filtered liquid.
2. Do not use a syringe smaller than 10cc, because the small-volume column may cause the pressure to exceed the upper limit and cause damage to the filter membrane.
3. Only for laboratory use, one-time use, non-renewable.
4. The filtrate at the beginning of the part should be discarded. The volume is about the dead volume of the filter. Taking 25mm as an example, discard the first 1mL filtrate; or pre-clean the filter with 1 to 2mL of solution.

In the sample application of choosing the appropriate syringe filter and syringe, draw your sample into the syringe and place the filter on the syringe. If you are using a leur lock filter, make sure you have properly secured the filter into the syringe tip .Push a few drops through the filter with the syringe filter facing up and “top”. Place the filter in the overturned collection container and push the sample through the syringe filter by applying gentle positive pressure. The syringe filter to be cleared and the maximum To maximize sample throughput, remove the filter from the syringe and draw air into the syringe. Then reinstall the filter and push the plunger to force some air through the filter.

The advantages of nylon: 1. Toughness 2. Wear resistance 3. Smoothness 4. Light weight 5. Insect resistance 6. Anti-mold and the material is not easy to generate static electricity, deformation, pilling and ageing.

Features of the syringe filter: Luer lock inlet provides a sealed syringe connection, with various filter types, porosities and diameters. Color coding is easy to identify. Rugged polypropylene shell. Can be autoclaved to 121℃ for 15 minutes. The quantity exceeds the minimum order quantity to save more.

The use of PTFE syringe filters can be used for corrosive solvents, aerosol sampling, degassing agents, exhaust applications and organic-based HPLC filtration. The syringe filter has a variety of different filter covers, and has a wide range of chemical compatibility, and has strong chemical stability and inertia.

Aijiren’s CA Syringe Filter 90% is exported to the world’s major economically developed countries. Filters can provide foundry services according to customer needs. The produced filters have good consistency between batches, and there are strict control procedures from raw materials to production processes to in and out of warehouse delivery management to ensure the quality and use value of the products.

Hydrophobic PTFE (Polytetrafluoroethylene) syringe filters are suitable for gaseous and organic solutions, with excellent performance for high corrosive samples. It is possible for an extended sampling range using hydrophobic PTFE filters for wider chemical resistance to aggressive substances and outstanding temperature stability. A PTFE syringe filter is an ideal choice for filtering and de-gassing chromatography solvents.

Syringe filtration is a crucial technique in laboratory settings, playing a vital role in sample preparation for various analytical methods.

PES syringe filter is hydrophilic in nature, and has low protein binding, high flow rate and excellent chemical stability. In addition, it also contributes to oxidation stability, high heat and low concentration of extractable elements.

The Syring Filter with nylon membrane produced by Aijiren has good hydrophilicity, acid and alkali resistance, and oxidation resistance. It is not only suitable for aqueous solutions containing acids and alkalis, but also for organic solvents such as alcohols, hydrocarbons, lipids, phenols, ketones and other organic solvents. It can be used for organic solvents such as strong acid, 70% ethanol, dichloromethane and so on. High temperature resistance, good strength, stable chemical properties.

Membrane separation technology is hailed as “one of the most promising high-tech developments in the middle of the 21st century”. Among them, microporous membrane separation is the most eye-catching application in the fields of biology, chemical analysis and pharmaceuticals. There is no need to change the membrane and clean the filter, save the complicated and time-consuming preparation work, and is widely used in the laboratory.

Hydrophilic nylon membranes have extremely low levels of extractables and contain no wetting agents. They offer good chemical resistance and are ideal for aqueous and most organic samples. Filters are Triton-free and have a bidirectional membrane support and luer lock inlet/outlet for a secure fit to the syringe. Membrane type and pore size are printed on each filter for easy identification. All Cole-Parmer syringe filters are 100% integrity tested and manufactured in accordance with ISO 9002 standards. Sterile filters are sterilized by gamma radiation. They are certified nonpyrogenic, noncytotoxic, and are blister packed.

Syringe filter is a small, disposable device used for filtering liquids or gases.It consists of a plastic housing with a membrane filter at one end and a female luer lock or luer slip connection at the other end, which allows it to be attached to a syringe or other fluid delivery system.
Syringe filters are commonly used in laboratory and research settings to remove particles, microorganisms, or other impurities from samples before analysis or further processing. The membrane filter in a syringe filter acts as a barrier, allowing only the desired components of the sample to pass through while retaining any larger particles or contaminants.
The choice of membrane material depends on the nature of the sample and the substances to be filtered.

Aijiren’s PVDF membrane (imported packaging, 6.6¡Á8.5cm, 0.2¦Ìm) is a pre-cut polyvinylidene fluoride (PVDF) imprinting membrane with a size of 6.6¡Á8.5cm and a pore size of 0.2¦Ìm. It is most commonly used for the transfer of protein from gel to membrane in immunoblot (Western blot), and can also be used for adsorption analysis, amino acid analysis, N-terminal protein sequencing, dot and slot blot detection, Glycoprotein color development and lipopolysaccharide analysis, etc.

Aijiren¡¯s PP syringe filter uses a hydrophobic polypropylene membrane, which has stable physical and chemical properties, good compatibility, low protein adsorption, and is suitable for filtration of aqueous solutions and most solvents. Commonly used to filter biological samples, solvents, deionized water and reduce biological load, the hydrophobic PP filter membrane is particularly good for gas filtration. The product was sterilized by dry heat at 121¡ãC for 15 minutes.

PTFE Syringe Filters are universal filters that are inert to a wide variety of aggressive solvents and strong acids and bases. These syringe filters can also be exposed to high temperatures and are an excellent choice for HPLC sample preparation. We offer PTFE syringe filters in both their hydrophobic and hydrophilic states.

Our Syringe Filters are high quality, well packaged and sold at a fair competitive price. They are available in most of the major membrane materials including Nylon, PTFE, PES, MCE, PVDF, CA, PP, and GF which are supplied in 13mm, 17mm, 25mm and 30mm formats in virgin polypropylene housings.

The membrane materials produced by Aijiren are provided by the most famous people in the industry, and in the ISO9000 certified production process, under certified clean room conditions, the latest manufacturing technology is used to ensure high-quality and stable products to achieve the highest standards . All syringe filters are HPLC certified.

1.ISO9001 approved
2.Imported from Germany and US to ensure high quality
3.Manufactured in 100,000 class cleaning room
4.Wide range size and customized.
5.OEM service available
6.Low backfround response
7.Board membrane choice with excellent compatibility with aqueous , organic solvent or their mixtures.

Convenient and Easy to Use£ºPES Syringe filters can be sterilized by autoclave at 125¡ãC for 15 minutes£¬Enhanced Luer Lock inlet prevents leakage; outlet fitting is a standard size male Luer-slip fitting for ease of filtrate collection, Come in bulk packs of 100 and not individually wrapped

In HPLC analysis, the particle size of the chromatographic column packing is small and easily blocked by contaminant particles. Therefore, samples and solvents must be pre-filtered to remove particulate contaminants and protect the instrument.

Aijiren disposable MCE syringe filter units are designed to provide clear filtration of aqueous and organic solutions from small volumes up to 100 mL.
MCE syringe filters are made from mixed cellulose ester (MCE) membrane and polypropylene overmolded housing.

Unique raised column structure with 0.45μm PES membrane processes double sample volume vs conventional filters, extending service life.