PVDF Syringe Filter Chromatography

Another way to determine the micron size of columns, 0.45 um for >3 um, and 0.22 um for <3um. 0.45 um membranes are typically used for general filtration and particle removal while 0.2/0.22um membranes, or sterilizing-grade membranes, are most commonly used for solution sterilization (bacteria removal).

Membrane separation technology is hailed as “one of the most promising high-tech developments in the middle of the 21st century”. Among them, microporous membrane separation is the most eye-catching application in the fields of biology, chemical analysis and pharmaceuticals. There is no need to change the membrane and clean the filter, save the complicated and time-consuming preparation work, and is widely used in the laboratory.

They are also very useful in the protection of vacuum pump pipelines and have the qualities of high absorption and retention capacity. Due to their advantages, these syringes can be used in laboratory situations as well as industrial applications.

The PES film is sealed in the polymer shell without the use of any adhesive. Each unit can provide ETO or Gamma radiation disinfection, and ensure that there is no pyrogen.

Syringe filter is a quick, convenient and reliable filter tool used routinely in the laboratory.Because they don’t need to change the membrane and filter cleaning, it’s eliminating the complex and time-consuming preparation. It is widely used in the sample pre filtration, removal of particles, aseptic filtration of liquids and gases. It is the preferred method to filter small samples before loading into HPLC and GC ,and it is often used with disposable syringe.

Our Syringe Filters are high quality, well packaged and sold at a fair competitive price. They are available in most of the major membrane materials including Nylon, PTFE, PES, MCE, PVDF, CA, PP, and GF which are supplied in 13mm, 17mm, 25mm and 30mm formats in virgin polypropylene housings.

Instructions for use and precautions:
1. It must be used with disposable syringes and glass syringes. The interface is standard. Put the needle filter on the syringe first, then pour the liquid into the syringe, press the push rod down, and collect the filtered liquid.
2. Do not use a syringe smaller than 10cc, because the small-volume column may cause the pressure to exceed the upper limit and cause damage to the filter membrane.
3. Only for laboratory use, one-time use, non-renewable.
4. The filtrate at the beginning of the part should be discarded. The volume is about the dead volume of the filter. Taking 25mm as an example, discard the first 1mL filtrate; or pre-clean the filter with 1 to 2mL of solution.

Cellulose acetate is a very low protein binding membrane that is ideal for aqueous based samples and biological samples. It is a lower protein binder than either polyethersulphone or PVDF membranes, but has a lower chemical resistance than regenerated cellulose (RC). CA is a strong membrane mechanically and hydrophilic.

Our Syringe Filters are high quality, well packaged and sold at a fair competitive price. They are available in most of the major membrane materials including Nylon, PTFE, PES, MCE, PVDF, CA, PP, and GF which are supplied in 13mm, 25mm formats in virgin polypropylene housings.

The use of PTFE syringe filters can be used for corrosive solvents, aerosol sampling, degassing agents, exhaust applications and organic-based HPLC filtration. The syringe filter has a variety of different filter covers, and has a wide range of chemical compatibility, and has strong chemical stability and inertia.

Aijiren syringe filter membrane use method introduction: before inhaling the sample, suck about 1ml of air into the syringe, so as to minimize the liquid residue, suck the sample into the syringe, invert the syringe and clear all the residues on the top Clean, connect the needle filter to the syringe, tighten it gently to ensure a good seal, filter the sample in the syringe and inject it into the sample bottle, and then follow the steps to maximize the recovery rate, remove the filter, and suck air into the syringe, Reconnect the filter head and eject all residual samples.

Aijiren’s PVDF syringe filter has hydrophilicity and good chemical compatibility. They can bring precision to your research and ensure the highest level of performance. Our filter series are designed with female Leur-lock inlet and male Leur-slip outlet. In addition, these filters have better mechanical resistance and can withstand high temperatures.

The hydrophobic PTFE syringe filter membrane is made of hydrophobic polytetrafluoroethylene. It filters organic solvents, aqueous solutions and gases that are chemically corrosive, and can withstand most strong acid and alkaline solutions. Product application: Used for the clarification and filtration of strong acids and alkalis, the filtration of high-temperature liquids and special chemical reagents, and the clarification and filtration of air or various gases.

MCE features: relatively uniform pore size, high porosity, no media shedding, thin texture, low resistance, fast filtration rate, and minimal adsorption.
The main purpose of MCE: to filter out the particles and bacteria of liquid medicine, gas, oil, beverages, sprinkles, electronic instruments, etc., and can also be used for the detection of particles and bacteria.

PTFE Syringe Filter is resistant to almost all corrosive chemicals, which makes PTFE syringe filters an ideal choice. However, the disadvantage of natural hydrophobic PTFE is that after many chemicals are diluted with water, the aqueous solution cannot pass through. Need to be wetted with water in advance.

13mm, 25mm 0.22um, 0.45um hydrophobic PVDF (polyvinylidene fluoride) membrane syringe filter is a filtration device commonly used in laboratory settings to remove particulates and microorganisms from fluids.
It’s important to note that specific details of hydrophobic PVDF membrane syringe filters, such as pore size, diameter, and filtration capacity, can vary between manufacturers and product lines.
Therefore, it’s recommended to consult the product specifications or contact the supplier for precise information about the syringe filters you are considering for your specific application.

The Lab Use Syringe Filter MCE is a versatile filtration tool designed for laboratory applications. Constructed with high-quality mixed cellulose ester (MCE) material, these syringe filters offer excellent chemical compatibility and durability. They effectively remove particulates, microorganisms, and impurities from liquid samples, ensuring enhanced sample purity for accurate analysis.

1.ISO9001 approved
2.Imported from Germany and US to ensure high quality
3.Manufactured in 100,000 class cleaning room
4.Wide range size and customized.
5.OEM service available
6.Low backfround response
7.Board membrane choice with excellent compatibility with aqueous , organic solvent or their mixtures.

Aijiren’s syringe filters and vials reduce HPLC sample preparation time and the use of consumables, and the track-etched membrane is also essential for extruding liposomes for encapsulation and targeted drugs.

The PTFE Syringe Filter in the picture has an aperture of 0.22, an outer diameter of 25mm, and a purple color. Aijiren also offers many other colors of Syringe Filter, such as yellow, pink, blue, green, etc. Customers can choose according to their preferences . The Syringe Filter produced by Aijiren can be equipped with many different types of filter membranes, which can be selected according to the reagents that customers need to filter.

Mainly used in the following aspects: HPLC sample preparation; conventional QC analysis; content uniformity; removal of protein precipitates; dissolution test; food analysis; biofuel analysis; environmental samples

PTFE is hydrophobic and needs to be pre-wetted before being used with aqueous solvents. Used for: corrosive solvents, strong acids, alcohols, alkalis, aromatic hydrocarbons. Not suitable for: water-based samples.

When using vents, these syringe filters can prevent moisture from passing through. Usable pH range: 1-14. PTFE can be applied to: filtering organic solvents with strong chemical corrosiveness, filtering strong acid solvents, filtering alkali solvents, compatible with gaseous samples, and can handle high-temperature liquids.

The Syring Filter with nylon membrane produced by Aijiren has good hydrophilicity, acid and alkali resistance, and oxidation resistance. It is not only suitable for aqueous solutions containing acids and alkalis, but also for organic solvents such as alcohols, hydrocarbons, lipids, phenols, ketones and other organic solvents. It can be used for organic solvents such as strong acid, 70% ethanol, dichloromethane and so on. High temperature resistance, good strength, stable chemical properties.

The nylon membrane used in the syringe filter has high mechanical strength, chemical stability, can be tolerated by most organic solvents, has very low extractables, has good thermal stability and natural hydrophilicity, and is filtered by most aqueous solutions characteristic.

Syringe Filters with hydrophobic PTFE membranes can be used for filtration of strong solvents, acids and alkalis. Not suitable for filtration of aqueous liquids. Filters with hydrophilic PTFE can be used for filtration of strong solvents, acids and alkalis. However, these syringe filters can also be used for the filtration of aqueous liquids, which makes this type very versatile.