Wide Mouth Gl45 Reagent Bottle

Reagent Bottle is suitable for general laboratory use, including mixing, storing or transporting culture media, chemicals or solvents. White enamel paint with chemical resistance, enhanced nicks and spots, can be autoclaved, with GL 45 threaded cap, each bottle has a replaceable clean (natural) non-drip polypropylene casting ring, from USP compliance Manufacture of type I and ASTM E438 type I, and type A requirements of 33 kinds of expansion type low extractable borosilicate glass

The reagent bottle can withstand a low coefficient of thermal expansion (3.3), and its heat resistance is far better than standard laboratory glass (or soda lime glass). Aijiren glass can withstand temperatures from -70 to 500°C, so it can be reused in freezers, microwave ovens, autoclaves and dry heat sterilizers.

The reagent bottle, also called the culture medium bottle or graduated bottle, is a container made of glass, borosilicate or related substances and covered with a special cap or stopper. They are intended to be used in the laboratory for chemicals in liquid or powder form and are stored in cabinets or shelves.

The reagent bottle produced by Aijiren has a low thermal expansion coefficient (3.3), which provides far better heat resistance than standard laboratory glass (or soda lime glass). Aijiren glass can withstand temperatures from -70 to 500°C, so it can be reused in freezers, microwave ovens, autoclaves and dry heat sterilizers.

The reagent bottle is made of borosilicate glass or soda-lime glass, with a stopper or cover, which can prevent the contents from overflowing or external environmental pollution. Reagent bottles are very suitable for storing powders and liquids. The wide mouth of the reagent bottle makes it easy to fill or retrieve the contents. The cap and stopper of the reagent bottle should be selected carefully, because their material or lining may have a negative effect on the contents of the bottle.

With a large enough change in temperature, the neck of the bottle can actually crack if it shrinks too tight around the stopper. Additionally, if hot liquid is poured in the bottle, the liquid will form an air-tight seal between the stopper and bottle and as the liquid and steam in the bottle cool and shrink, the stopper will be pulled down into the bottle neck.? This is the same principle that makes the center of a canning jar lid pop down until the seal is released.

Bottles and screw caps can be autoclaved / sterilized. Made from borosilicate glass helps prevent changes in ph levels and maintain content purity. Non-slip coating allows for greater ease and stability when handling wet or dry. 45mm white polypropylene unlined screw cap comes attached to bottle to help maintain cleanliness. Pvc-based plastisol coats exterior of bottle retaining contents if bottle is accidentally broken.

Caps and stoppers for reagent bottles should be selected carefully, as their material or lining may interact negatively with the contents of the bottle.

Reagent bottle, also known as culture medium bottle or scale bottle, is a container made of glass, borosilicate or related substances, with a special cover on the top. They are designed to contain chemicals in the form of liquid or powder for laboratory use and are stored on cabinets or shelves. Some reagent bottles are amber (photochemical), brown or red to protect photosensitive compounds from visible, ultraviolet and infrared radiation, which may change them; Bottles are called “graded” when they are marked on the side to indicate the approximate (usually 10% error) amount of liquid at a given level in the container. Reagent bottle is a kind of laboratory glassware.

A low coefficient of thermal expansion (3.3), provides temperature resistance that is far superior to that of standard lab glass (or soda lime glass). Aijiren glass can withstand temperatures from -70 to 500°C, permitting repeated use in freezers, microwaves, autoclaves and dry heat sterilization chambers.

Features:
1. It is made of borosilicate 3.3 glass, which has the properties of chemical resistance, heat resistance and impact resistance. The unique design of the pouring ring at the mouth of the bottle avoids dripping during use.
2. For the convenience of use, reagent bottles with a capacity of 100ml and above all adopt uniform and replaceable screw caps and pouring rings.
3. The bottle body, bottle cap and pouring ring can be sterilized by high temperature and high pressure.
4. Suitable for sample collection for various liquid particle size testing, containing high-clean reagents, standard materials, and standard samples
5. Threaded bottle cap with good sealing performance, which can effectively isolate external magazines, dust and moisture
6. The specifications are clearly marked and the volume scale is obvious