16mm Test Tube for Water Analysis

Aijiren COD Test Tube is small in size and light in weight. It can be tested without any other laboratory equipment and technicians; it only takes 3-5 minutes to test a sample, without additional materials or instruments, and is easy to operate.

COD Test Tube is one of Aijiren’s main products. It can complete many important experiments, such as digestion colorimetry, water quality test, oxygen demand test, etc. The COD Test Tube produced by Aijiren has high inertness, good quality and stable tube. Aijiren has become a well-known manufacturer of chromatography consumables in southern China by virtue of the good quality of COD Test Tube.

To use the digital heater for the COD test, set the temperature on the digital display to 150°C. On no account must the heater be set at a higher temperature than that specified as this may cause a hazard through pressure build-up in the COD tubes.

Aijiren uses high-quality raw materials to make 16mm Test Tube for Water Analysis. Customer satisfaction and praise have made Aijiren one of the largest laboratory consumables producers in southern China. First, Aijiren will stick original intention to ensure the quality of 16mm Test Tube for Water Analysis.

Suitable for colorimeters and test kits on the market
Also suitable for instruments and test kits
Easy-to-open sealed vials eliminate the risk of cross-contamination
Extend the shelf life to five years
Used for municipal wastewater testing; industrial wastewater and process control testing; environmental water testing

Water Sample Cell
Color: Clear
Volume: 20ml, 30ml
Size: 25x60mm, 25x95mm
Cap: with black cap

The used COD Tubetests contain strong sulfuric acid and other chemicals, so reagents must be handled carefully. The contents of the pipe should be disposed of in accordance with the requirements of local authorities.
These test tubes are SGC certified. These tubes can only be used once, so they cannot be reused.

This COD test tube is designed with precision and functionality in mind. It features a rugged construction that can withstand the rigors of COD testing, including high temperatures and exposure to various chemicals.

20ml water sample cell with cap, clear, 25*60mm, flat bottom; 25mm FTU test vials, 6 pcs/pk

Tube tests for photometric analysis convince by their easy handling and therefore are the first choice for routine, laboratory and process analysis. A maximum in accuracy and precision is granted for the measurement results due to exactly pre-dosed reagents in 16 mm cuvettes and additional reagents.

TOC is the abbreviate by Total Organic Carbon. The TOC Direct Method from Aijiren provides a reliable and practical means for water treatment facilities to frequently measure organic carbon to optimize treatment processes. Instead of purchasing an expensive, traditional TOC analyzer or outsourcing TOC determinations to a contract laboratory, this method can provide TOC results — accurately and inexpensively — right at your facility, and without any hazardous waste.

Details of Chemical Oxygen Demand Test:

2mL of a water or watse water sample are added to a 16mm glass culture tube containing the digestion reagent and a catalyst. The tube is capped with a polypropylene, PTFE lined cap and heated in a block digester at 150C for 2 hours. The orange Hexavalent chromium is reduced to a greenish trivalent chromium. The analytical range for the spectrophotometric method is 5-150ppm (measured at 420nm).

Reusing caps and vials opens up the possibility of contamination, from solvent (liquid or vapor) interacting with the septa material as well as the atmosphere. This may seriously impact your analytical results, causes by sample contamination, chemical reaction, or evaporation. Both qualitative and quantitative errors may result, requiring time consuming, expensive, and frustrating troubleshooting and re-work.

The Chemical Oxygen Demand (COD) test is widely used as a measure of organic contamination by determining the quantity of oxygen required for oxidation of reduced species including organic matter, in a water sample using a specific oxidizing agent, temperature and time reduction. COD testing is a good better indicator of organic pollutants in industrial wastewater containing cyanides and heavy metals. COD testing affords rapid response to changing conditions before critical problems develop.

In this test a reagent blank is used instead of the usual water blank referred to in the general photometer operating instructions. The reagent blank is prepared by adding deionised or distilled water to the reagent tube and then digesting the tube in the same manner as for the water sample.
It is not necessary to prepare a reagent blank each time the test is carried out. The reagent blank tube may be prepared weekly and used repeatedly with all samples prepared from the same batch of reagent tubes. The reagent blank should be stored in the dark between uses.

The COD Test Tubes produced by Aijiren are often used for chemical oxygen demand detection. The glass used in the COD Test Tubes produced by Aijiren has high temperature resistance, corrosion resistance, and can well protect the samples without affecting the experimental results. Aijiren’s raw materials are of high quality and production experience Abundant, with favorable product prices, it is a high-quality supplier of chromatographic consumables.

With the Aijiren COD tube test, each user can easily perform highly sensitive and accurate water detection. The time required for the measurement process is greatly shortened, especially for standard analysis and series measurement, while greatly reducing the workload.

The COD tube provided by Aijiren uses high-quality glass, which is extremely inert and will not react with reagents. Through Aijiren COD tube test, the time required for the measurement process is greatly shortened, especially for standard analysis and series measurement, which greatly reduces the workload.

Glass test tube is a cylindrical container made of glass that is commonly used in scientific laboratories for holding, mixing, and heating small quantities of liquid or solid substances. Test tubes are usually open at one end and have a rounded or slightly flared bottom. They come in various sizes, ranging from a few centimeters to several centimeters in length.
Test tubes are designed to withstand high temperatures and chemical reactions, making them suitable for a wide range of experiments and analyses.