Vial Closure Size: 9mm Vial Volume (Metric) 1.5mL Volume (Metric) Working 1.3mL Material: Glass Color: Amber Height (Metric) 32mm Outside Diameter (Metric) 12mm Residual Volume: <4μL
“Aijiren Vials have a standard 11.6x32mm profile and are compatible with convenient 11mm snap cap or aluminum seal closures The “Step” design ensures proper centering of limited volume inserts, eliminating missed injections Aijiren Vials have a 40% larger opening than standard aluminum seal vials for easier sample filling and to reduce the chance of bent or broken needles during sampling”
2ml clear crimp top hplc autosampler vial is made of borosilicate glass. Comparing with 2ml amber crimp headspace vial, the 2ml clear crimp top hplc autosampler vial should be made by special process. The appearance of a clear and transparent 2ml crimp top sample hplc vial has attracted widespread attention. 2ml clear crimp top hplc autosampler vial is made by adding UV-absorbed metal oxides to the glass, while using the complementary effect of color, and then adding certain metals or their oxides to fade the colored glass. So in theory, the 2ml clear crimp top HPLC autosampler vial is a little expensive than Amber autosampler vial.
Amber Borosilicate Glass ND9mm Screw Neck Vial 11.6*32mm With Writing Spot 9mm Blue Short Screw PP Cap with 6mm Centre Hole Pre-slit / non-slit PTFE Silicone Septa Septa Size: 9*1mm
Caps with solid PE liners offer good chemical resistance and low moisture vapor transmission rate and is great for nail polish remover and higher concentration acids & alkalis. Good for non-oil products filled at room temperature. Because this lining system is paperless, your samples will not be contaminated with fiber or paper particles from the closure. Available in Phenolic caps.
9-425 short thread vials with screw caps wholesale, the best supplier in China Aijiren provides chromatography vials, caps, vial inserts, syringe filters for hplc, glass reagent bottles, etc Suitable for most autosampler use in the market
Thread: 10mm diameter Separator: PTFE/silicone composite layer Separator thickness: 1.5mm Compatibility: compatible with 10-425 sample bottles and all 10-425 threaded injectors
If the reagent to be tested by the customer is very precious and the capacity of 2ml vial is too large, Aijiren 8-425 2ml Autosampler Vials can be used with different types of micro-insert. There are 3 types of micro-insert, 29*5mm 150uL micro-insert with mandrel interior&polymer feet, 150uL conical bottom micro-insert and 250uL flat bottom micro-insert. All three types of micro-insert can be adapted to 8-425 2ml Autosampler Vials.
Aijiren screw thread top sample vials design is characterized by universal ease of use, especially the use of automated sample introduction systems, so this type of vial is also called a autosampler vial. And this sample vial is extremely compatible. The 1.5ml sample vial we usually say is the 2ml volume sample vial. The design of Aijiren screw thread top vials are developed from Europe and the United States, and the design feature is easy to use, especially the use of automated sample introduction system. Aijiren screw thread top vials also known as autosampler bottles.
The thread design of the 8-425 threaded sample vialcan make the septum achieve extremely strong re-tightness, so this sample vial can also be used as a storage vial, and it can also be used for autosampler. This design sample vial is mostly suitable for Shimadzu Hitachi and other Japanese enterprise instruments.
2 ml HPLC borosilicate glass vials are commonly used in high-performance liquid chromatography (HPLC) for sample storage and analysis. Borosilicate glass is preferred in HPLC because it offers excellent chemical resistance and thermal stability, making it suitable for handling a wide range of solvents and temperature conditions.When working with water samples in HPLC, borosilicate glass vials are a suitable choice due to their resistance to water and other polar solvents.
Caps are made of high quality polyproylene to exact manufacturing tolerances and lined in a controlled manufacturing environment, Cap colors are available in black only, Our septa use only the highest quality materials to ensure proper function and can be pre-slit to ease needle penetration.
The function of crimping top sample vials, Strict quality assurance provides dimensional consistency between batches, Optional ceramic write points with filling marks, Certified and fully compatible with autosampler.
Aijiren Crimp Top vials are excellently fitted for autosamplers and have good chemical compatibility and super cleanliness. The crimp top sample vial is the most commonly used gas sampling vial on the market at present. 2ml volume sample vial especially suitable for laboratory use. At the same time, it has a flat bottoming function and compatibility with automatic sampling equipment.
1.5ml HPLC borosilicate glass vials are a type of autosampler vials specifically designed for use in High-Performance Liquid Chromatography (HPLC) applications. HPLC is a widely used analytical technique that separates, identifies, and quantifies components in a liquid sample. 1.5ml HPLC borosilicate glass vials are commonly used in pharmaceutical, environmental, and other analytical laboratories where HPLC analysis is performed.
The Aijiren 8-425 screw cap and vial are suitable for waters and other rotating or robotic arm samplers. The specifications for the 8-425 HPLC sample vial are 12 x 32 mm. The opening of the 8-425 HPLC sample vial is 40% larger than the standard narrow opening vial, preventing syringe problems. Accurately handle bottlenecks and enable the mechanical arm to operate efficiently. The special screw design ensures a consistent seal.
Padded 2ml snap top Autosampler vials are widely used in experiments. The pads are made from PTFE and high quality silicone rubber or ultra-high purity silicone as raw materials. Make sure the gasket is non-toxic. Using an adhesive-free adhesive process, PTFE film and silicone rubber or silicone adhere and maintain a composite post-interval Teflon layer contact reagent with good properties, good chemical inertity of the two materials.
The Screw Caps that are inlcuded with this kit are knurled on the sides for excellent gripping and comfort when applyting to the vial. The silicone rubber / PTFE septa used were designed to provide the right amount of resistance to autosampler needles during the injection process so that they penetrate the vial properly without damaging the septa or the injection needle. Too much or too little resistance to the needles can damage the septa, compromise resealing, cause needle blockage from coring of the septa material and even damage your autosampler. These septa perform even when using a wide range of needles: fine, blunt or even dull. Low sample or solvent evaporation performance even after multiple injections have been observed when using aijiren caps.
2ml UPLC (Ultra-Performance Liquid Chromatography) is a high-pressure liquid chromatography technique used for separating and analyzing chemical compounds. When working with UPLC, it’s important to choose appropriate vials and caps to ensure sample integrity and compatibility with the system.
Aijiren 2ml snap neck has 40% lager target area which makes it much safer for the autosampler needle. Snap vials can be closed with either snap caps or crimp caps. Snap cap vials cannot be pressurized, but can be easy as push-on, pull-off by hand. A audible click ensures a secure seal has been formed and that the cap is correctly aligned. Precision-formed neck improves autosampler handling.
1.5ml/2mlSnap autosampler borosilicate glass vial refers to a type of vial commonly used in laboratory settings for sample storage and analysis. Borosilicate glass is chosen for its excellent resistance to thermal shock, chemical durability, and low contamination potential. The term “Snap autosampler” typically refers to an automated instrument used in analytical chemistry, specifically in chromatography. It is designed to automatically inject samples into the chromatographic system for analysis. The vials used with such autosamplers need to be compatible with the instrument’s design and specifications.
2mL Amber Glass Screw Top Autosampler Vials are available in a variety of neck finishes and opening diameters. Large mouth or wide ID vials have approximately a 40% wider mouth opening than standard opening vials. The large opening reduces the risk of bent autosampler needles during sampling. When choosing a 2mL Amber Glass Screw Top Autosampler Vials, the product material is of paramount importance.
Aijiren 9-425 HPLC Vial can choose the type with writing area and scale for easy filling and identification of samples. Aijiren 9-425 sample vials can be used with the robotic arm autosampler. The opening of the 9mm sample vial is 40% larger than that of ordinary vials to facilitate sample preparation. The Aijiren 9-425 sample vial must be used together with the 9mm screw pp bottle cap. Ensure proper fit and function.
Suit for: 9mm Short Thread Vials Caps Material: polypropylene Cap Diameter: 9mm Cap Features: 6mm Centre Hole or Closed Top Septa Material: PTFE / Silicone Septa Feature: Pre-slit I or X Septa diameter: 9mm Septa Thickness: 1mm
Aijiren’s 8-425 2ml Autosampler Vials is very popular. It is favored by our customers for its high quality and cheap price. Aijiren is a manufacturer of 8-425 2ml Vials, so we bring our customers to the factory price.Buy 8-425 vials,Choose Aijiren.
Let me introduce the material of 8-425 2ml autosampler vials, 33 Expansion borosilicate glass USP Type I Class A made of clear vial, or 51 Expansion borosilicate glass USP Type I, Class B made of Amber vial.Our glass uses neutral borosilicate and low borosilicate, but our neutral borosilicate can reach the standard of high borosilicate, and our low borosilicate can reach the standard of neutral borosilicate. We use excellent raw materials to make 8-425 2ml autosampler vials.
Material: Brosilicate Glass/1st hydrolytic class glass Volume: 1.5-2.0ml Dimension: 11.6x32mm Neck: 9mm Screw neck Color: Amber and Clear Septa: Pre-Slit, PTFE/Silicone OEM & ODM Custom Service
Glass Screw Vials ND9mm for HPLC, Clear & Amber, with /without Patch High Recovery Glass Screw Vials ND9mm, Clear & Amber, with /without Patch 0.3ml Glass Screw Vial integrated with Micro-insert, Base Bonded, Clear & Amber, with /without Patch PP Screw Vials ND9mm, Clear & Amber 0.3ml PP short Screw Micro Vials, Clear & Amber
