Black Cap for 16mm COD Test Tube for Supplier

COD Test Tube is one of Aijiren’s main products. It can complete many important experiments, such as digestion colorimetry, water quality test, oxygen demand test, etc. The COD Test Tube produced by Aijiren has high inertness, good quality and stable tube. Aijiren has become a well-known manufacturer of chromatography consumables in southern China by virtue of the good quality of COD Test Tube.

Aijiren uses high-quality raw materials to make 16mm Test Tube for Water Analysis. Customer satisfaction and praise have made Aijiren one of the largest laboratory consumables producers in southern China. First, Aijiren will stick original intention to ensure the quality of 16mm Test Tube for Water Analysis.

Tube tests for photometric analysis convince by their easy handling and therefore are the first choice for routine, laboratory and process analysis. A maximum in accuracy and precision is granted for the measurement results due to exactly pre-dosed reagents in 16 mm cuvettes and additional reagents.

COD digestion vials are specialized containers used in chemical analysis for determining the chemical oxygen demand (COD) of a water sample. COD is a measure of the amount of oxygen required to chemically oxidize the organic and inorganic compounds present in the water.
These vials are typically made of high-quality glass or borosilicate glass, which is resistant to chemical reactions and can withstand the high temperatures necessary for the COD digestion process. The vials are designed to hold a specific volume of the water sample and the reagents required for the COD test.

Reusing caps and vials opens up the possibility of contamination, from solvent (liquid or vapor) interacting with the septa material as well as the atmosphere. This may seriously impact your analytical results, causes by sample contamination, chemical reaction, or evaporation. Both qualitative and quantitative errors may result, requiring time consuming, expensive, and frustrating troubleshooting and re-work.

Aijiren COD Test Tube is small in size and light in weight. It can be tested without any other laboratory equipment and technicians; it only takes 3-5 minutes to test a sample, without additional materials or instruments, and is easy to operate.

To use the digital heater for the COD test, set the temperature on the digital display to 150°C. On no account must the heater be set at a higher temperature than that specified as this may cause a hazard through pressure build-up in the COD tubes.

Suitable for colorimeters and test kits on the market
Also suitable for instruments and test kits
Easy-to-open sealed vials eliminate the risk of cross-contamination
Extend the shelf life to five years
Used for municipal wastewater testing; industrial wastewater and process control testing; environmental water testing

This COD test tube is designed with precision and functionality in mind. It features a rugged construction that can withstand the rigors of COD testing, including high temperatures and exposure to various chemicals.

The COD tube provided by Aijiren uses high-quality glass, which is extremely inert and will not react with reagents. Through Aijiren COD tube test, the time required for the measurement process is greatly shortened, especially for standard analysis and series measurement, which greatly reduces the workload.

In this test a reagent blank is used instead of the usual water blank referred to in the general photometer operating instructions. The reagent blank is prepared by adding deionised or distilled water to the reagent tube and then digesting the tube in the same manner as for the water sample.
It is not necessary to prepare a reagent blank each time the test is carried out. The reagent blank tube may be prepared weekly and used repeatedly with all samples prepared from the same batch of reagent tubes. The reagent blank should be stored in the dark between uses.

Open COD test tube, hold it at an angle and slowly add
2.0 mL of the pretreated sample solution from the reaction tube without mixing so that two separate layers
are formed.
Screw cap securely on to test tube, hold tube by the cap, place tube into the safety bottle and shake
(Caution, test tube becomes hot). Place tube into the heating block. Start heating programme.
After 2 h remove test tube from heating block, allow to cool down to room temperature and shake gently
several times.
Clean outside of test tube and measure.
Adjust photometer to zero by using blank value “NULL”

The used COD Tubetests contain strong sulfuric acid and other chemicals, so reagents must be handled carefully. The contents of the pipe should be disposed of in accordance with the requirements of local authorities.
These test tubes are SGC certified. These tubes can only be used once, so they cannot be reused.

With the Aijiren COD tube test, each user can easily perform highly sensitive and accurate water detection.
The time required for the measurement process is significantly shortened, especially for standard analysis and series measurement, while significantly reducing the workload.
The COD Test tube contains a precise dose of reagent. Therefore, excessive chemical inventory is avoided and work safety is improved.

Chemical oxygen demand is a vital test for assessing the quality of effluents and waste waters prior to discharge. The Chemical Oxygen Demand (COD) test predicts the oxygen requirement of the effluent and is used for monitoring and control of discharges, and for assessing treatment plant performance. The impact of an effluent or waste water discharge on the receiving water is predicted by its oxygen demand. This is because the removal of oxygen from the natural water reduces its ability to sustain aquatic life. The COD test is therefore performed as routine in laboratories of water utilities and industrial companies.

The Chemical Oxygen Demand (COD) test is widely used as a measure of organic contamination by determining the quantity of oxygen required for oxidation of reduced species including organic matter, in a water sample using a specific oxidizing agent, temperature and time reduction. COD testing is a good better indicator of organic pollutants in industrial wastewater containing cyanides and heavy metals. COD testing affords rapid response to changing conditions before critical problems develop. Lovibond’s COD vials are compatible with BOTH Lovibond and Hach® colorimeters.

The COD Test Tube produced by Aijiren has a capacity of 10ml, 12ml, and 15ml. The caliber is 16mm. It is often used for water quality testing and contains liquid reagents. It is mostly used in the petroleum industry and chemical analysis.

Test Tube is a term that can refer to different things depending on the context. In a scientific context, a test tube is a cylindrical glass or plastic tube used to hold and mix small amounts of liquid during experiments in laboratories. It is commonly used in chemistry, biology, and other scientific disciplines.
In a broader sense, “Test Tube” can also refer to a YouTube channel called “TestTube,” which is a popular science and educational channel owned by Discovery Digital Networks. The channel covers a wide range of topics, including science, technology, history, and culture, and provides informative and entertaining videos for viewers.

The 16mm COD Test Tube produced by Aijiren is mostly used for laboratory chemical analysis. Aijiren believes that COD Test Tube requires high-quality raw materials and advanced technology to complete the production, so Aijiren is very attentive to the production of COD Test Tube. Aijiren has been a veteran in the field of chromatography consumables with 20 years of production experience. He still maintains his original intention and puts the improvement of product quality in the first place.